Knowledge · Guide

Connect NMEA to the Logbook app over Wi-Fi

You connect the Logbook app to your onboard network in four steps: join the Wi-Fi, pick your gateway, turn the connection on, set the data source order. The app figures out on its own whether NMEA 0183, NMEA 2000, or Signal K is coming in.

Updated: November 2026

What you need

  • A device on board that makes your instrument data available over Wi-Fi: an NMEA-to-Wi-Fi gateway, a multiplexer or chartplotter with Wi-Fi, or a Signal K server. You'll find a selection further down.
  • Your phone or tablet on the same Wi-Fi network.

Step 1: Join the right Wi-Fi network

Most gateways set up their own Wi-Fi network (access point). Connect your device to it. If the gateway is hooked into a router's onboard Wi-Fi instead, connect to the boat's Wi-Fi.
The first time around, iOS asks whether the app may find devices on your local network. Allow it, or no connection can be made.

Step 2: Pick your gateway

Open Settings › Data sources › NMEA connection settings and tap the first row under “Connection.”
Under Known Gateways you'll find 14 manufacturers with their factory settings. Tap yours, and protocol, IP address, and port are filled in.
If your device isn't on the list, enter the details yourself under Custom Settings:
FieldWhat goes in
ProtocolTCP, UDP, or Signal K (WebSocket). It's in your gateway's manual.
IP or HostnameThe gateway's address, for example 192.168.4.1. With UDP there's no such field: the app listens on the port for data from all devices on the Wi-Fi network.
PortThe port the gateway sends on, for example 10110.
$MXPGN Bytes in reverseOnly for the Shipmodul MiniPlex. Only turn it on if the values make no sense otherwise.
The values in the list apply to the gateway's own Wi-Fi network. If the gateway is on your onboard network, the router usually assigns a different IP address. The port stays the same.

Step 3: Turn the connection on and check it

Turn on NMEA Connection. The app checks the connection, which takes a few seconds. After that, the status shows the format it detected:
  • NMEA 0183
  • NMEA 0183 + NMEA 2000 (PCDIN/PGN)
  • NMEA 2000 (ASCII)
  • NMEA 2000 (binary)
  • Signal K
Below that, the Received Data list appears with live values, grouped by position, wind, water depth, engine, tanks, and so on. Here you can see at a glance what your onboard network delivers and which sentence or PGN each value comes from.
On the home screen, a label in the top right shows NMEA OK in green as long as data is coming in, and NO NMEA in red if nothing has arrived for 15 seconds.

Step 4: Set the data source order

This is the step that gets skipped most often. The app only puts an NMEA value into your entries once the NMEA source is first in the order for that value.
Out of the box, NMEA sits further down. The position, for example, comes from your phone's GPS first, and the wind comes from the internet first.
Here's how to change that:
  • Open Settings › Data sources › Define data sources.
  • Pick the value, for example “Water depth.”
  • Drag the NMEA source you want all the way to the top, for example “NMEA 0183 DPT” or “NMEA 2000 128267.”
  • Below it, decide what should happen when NMEA isn't delivering anything: the value from the internet, the value from the last entry, or no value.
The app works through the list from top to bottom and takes the first valid value. The check stops at “Leave the value empty,” “Previous value,” and “Calculated.” Anything below those is never used.
You can tell whether it's right in the NMEA settings: in the “Received Data” list, “1.” marks the source that goes into new entries. If no source is in first place for a value, the app points that out. Tap the note and you're taken straight to the order.
An NMEA value is valid for 60 seconds. If it's older, the app moves on to the next source in the order.

Useful settings

  • Water depth › Offset: Added to every depth reading received. Positive for the distance from the transducer to the waterline, negative for the distance from the transducer to the keel.
  • Trip log › Import: Total Log (never reset) or Trip Log.
  • Batteries › Import: Voltage in volts or state of charge in percent, per battery.
  • Alert when NMEA connection is lost: Under Settings › Advanced settings you can have the app notify you when the NMEA connection drops or data stops coming in.
More on engine, tanks, and batteries is in the guide Engine, tanks, and batteries over NMEA 2000.

Troubleshooting

When you turn the connection on, the app checks for itself where things are stuck and shows one of these messages:
Message in the appWhat it meansWhat to do
The hostname … could not be resolved.The name you entered isn't known on the network.Check the spelling or enter the IP address.
… is unreachable.The gateway isn't responding at all.Check that you're on the gateway's Wi-Fi and that the IP address is right.
… is reachable, but no service is responding on port ….The address is right, the port or protocol isn't.Compare port and protocol (TCP/UDP) with the gateway's settings.
No data is arriving on port ….The connection is up, but the gateway isn't sending anything.Check that the gateway outputs data on this port and that the instruments are on.
Data is arriving at port … that cannot be read.The format is unknown.Set the gateway's output format to NMEA 0183, NMEA 2000, or Signal K.
Other typical cases:
  • You're connected, but the values are missing from your entries: Step 4 is missing. The NMEA source has to be in first place.
  • A single value is missing from “Received Data”: Your onboard network isn't delivering it, or the gateway is filtering it out. Many gateways have filter lists for sentences and PGNs.
  • No more internet as soon as you're on the gateway's Wi-Fi: That's normal; the gateway's Wi-Fi has no internet access. Weather from the internet is then only available over cellular. The permanent fix is to have the gateway join a boat Wi-Fi network that has internet.
If you're stuck: In the NMEA settings, tap Export latest data entries and send me the file. It contains up to 1,000 data records received, and that usually shows me right away what's going on.

Supported hardware: IP addresses and ports

As a rule, any device works that provides NMEA 0183, NMEA 2000, or Signal K over Wi-Fi via TCP, UDP, or WebSocket. The list is neither complete nor final. If you're running a device that's missing here, I'd appreciate a quick note and I'll add it.

Preset in the app

You can pick these manufacturers directly under “Known Gateways.” Shown are the factory settings on the device's own Wi-Fi network.
ManufacturerIP addressProtocolPort
ACR192.168.4.1TCP24000
Actisense192.168.4.1TCP60001
AMEC192.168.1.1TCP3333
Digital Yacht192.168.1.1TCP2000
em-trak192.168.0.1TCP2000
nke192.168.56.1TCP50000
Ocean Signal192.168.4.1TCP24000
Plastimo192.168.53.1TCP40000
Quark-elec192.168.1.100TCP2000
Shipmodul10.0.0.1TCP10110
Signal K (NMEA 0183 output)192.168.1.1TCP10110
Signal K (JSON)192.168.1.1WebSocket3000
Vesper Marine192.168.15.1TCP39150
Yacht Devices192.168.4.1TCP1456

Devices customers are using

I know these devices are in use with the app. Enter these values under “Custom Settings” unless the manufacturer is listed above.
HardwareIP / portPriceComment
SWAY192.168.4.1 / port 10110 (UDP), 2001 (TCP)€ @ manufacturer sway-sailing.deAccording to the manual, it can also join an existing Wi-Fi network.
NMEA2000 WIFI Replicator10.10.1.1 / port 1343€ @ manufacturer TechnoSpark SystemsSupports TCP and delivers NMEA 2000.
SEAYAK Seatalk1 to NMEA WiFi Bridge192.168.4.1 / port 23€ @ manufacturer or eBayConverts SeaTalk 1 to freely accessible NMEA.
Vesper WatchMate XB-8000192.168.15.1 / port 39150€€€€€ @ manufacturersmartAIS transponder with Wi-Fi and NMEA 2000 gateway.
Yacht Devices NMEA 0183 Wi-Fi Gateway YDWN-02192.168.4.1 / port 1456€€ @ Amazon (affiliate link) / manufacturerWith a web server for configuration.
Yacht Devices NMEA 0183 Wi-Fi Router YDWR-02192.168.4.1 / port 1456€€€ @ Amazon (affiliate link) / manufacturerWith a web server for configuration; also speaks SeaTalk.
Yacht Devices NMEA 2000 Wi-Fi Gateway YDWG-02192.168.4.1 / port 1456€ @ Amazon (affiliate link) / manufacturerThe plug-in stick among NMEA-to-Wi-Fi converters.
QK-A024 AIS Receiver with NMEA Multiplexer + WiFi192.168.1.100 / port 2000€ @ manufacturerThe cheapest one.
Shipmodul MiniPlex-3Wi(-N2K)10.0.0.1 / port 10110€€€€ @ manufacturerMultiplexer that also handles SeaTalk. Pick “Shipmodul” in the app.
NSS8 chartplotter with GoFree Wifi-1 module192.168.0.10 / port 10110€€€ @ Simrad (NSS8 no longer sold)For use with Simrad multifunction displays.
B&G Zeus3192.168.76.1 / port 10110——
Easy TRX, by Weatherdock192.168.16.254 / port 8080——
Data Hub, PredictWind10.10.10.1 / port 11102€€€ @ manufacturer—
For links marked “(affiliate link),” I earn a commission if you buy through them. And if a link no longer works, I'd appreciate a heads-up about that, too.

Raymarine: Wi-Fi doesn't mean NMEA

Lots of Raymarine devices have Wi-Fi. Some of them only speak RayNet, a.k.a. SeaTalkHS, over it, though: a closed interface that only Raymarine apps understand and that I can't read. SeaTalk 1 and SeaTalk NG only exist on the cable.
The data has to show up on Wi-Fi openly as NMEA 0183, NMEA 2000, or Signal K. You get there with a gateway on the cable:
  • SeaTalk NG is electrically NMEA 2000. With an adapter cable, an NMEA 2000-to-Wi-Fi gateway fits.
  • SeaTalk 1 needs a SeaTalk-to-NMEA-to-Wi-Fi converter, for example the SEAYAK bridge from the list or, untested, this device on Amazon (affiliate link).

Supported NMEA 0183 sentences

The talker ID, meaning the two letters after the $, doesn't matter. $GPRMC, $GNRMC, and $IIRMC are treated the same. The app discards sentences with a bad checksum.
SentenceDelivers
RMCPosition, Speed and Course Over Ground
GGA, GNSPosition, GPS accuracy
GLLPosition
GSA, GSTGPS accuracy
VTGSpeed and Course Over Ground
HDT, HDGTrue heading (HDG only with magnetic variation in the sentence)
VHWTrue heading, current
VDRCurrent
MWV, MWD, VWR, VWTWind, see the wind guide
MDABarometric pressure, air and water temperature, true wind
MMBBarometric pressure
MTAAir temperature
MTWWater temperature
DPT, DBT, DBS, DBKWater depth
VLWTrip log (total and trip)
RPMEngine RPM
XDRTemperatures, barometric pressure, batteries, engine hours, RPM, tanks, heel, trim
The NMEA 2000 PGNs are in the guide Engine, tanks, and batteries over NMEA 2000, the Signal K paths in the Signal K guide.

What doesn't work

  • Several gateways at once. The app keeps one connection open. NMEA 0183 and NMEA 2000 can arrive mixed over it, and with UDP the app receives data from all devices sending on that port.
  • Bluetooth. The data has to come in over Wi-Fi.
  • Finding the gateway automatically. You pick IP address and port from the list or enter them yourself.
  • AIS targets. AIS sentences are received but not processed.
Need any of that? Get in touch with me. I'll do my best to find a solution.

Checklist: is everything running?

  • [ ] The status in the NMEA settings shows the detected format, and the home screen says NMEA OK in green.
  • [ ] Under “Received Data” there are live values for everything you want in your logbook.
  • [ ] For each of those values, an NMEA source carries the “1.” marker. A new test entry contains your instruments' values.

Frequently asked questions

Which IP address and port do I need to enter?

The factory settings of 14 manufacturers are preset in the app, and more are in the table above. Otherwise you'll find both values in the manual or on your gateway's configuration page. Common ones are 192.168.4.1 and port 10110, 2000, or 1456.

TCP or UDP: which should I pick?

Whichever your gateway offers. With TCP, the app connects specifically to the gateway's address. With UDP, the app listens on a port and accepts data from all devices on the Wi-Fi network, so you don't need an IP address.

Why aren't the NMEA values in my entries?

The NMEA source isn't in first place. Open Settings › Data sources › Define data sources and drag it to the top for that value.

Does my NMEA 2000 gateway have to convert the data to NMEA 0183?

No. The app reads NMEA 2000 directly, as $PCDIN, $MXPGN, Actisense ASCII or binary, and Yacht Devices RAW.

Can I use an iPad without GPS?

Yes. Under “GPS position,” drag the NMEA source to first place. The app then uses the position from the onboard network, for automatic recording too.